AirPal Platform Disinfection, Stain Removal, Laundry, Filter and Accessory Cleaning Guidelines

Wipe-Down Disinfectant Procedure ("L" and "N" Series):

Prior to any procedure please abide by your facility's standards for protective clothing and eyewear. All AirPal Platform Transfer Pads can be wiped down. AirPal recommends that the Platforms be used with the supplied or a disposable AirPal brand liner. In place of the liner the AirPal platform can be used with a linen sheet, incontinent pad, disposable chucks, etc. The AirPal brand reusable liners and Platforms require disinfectant wipe-downs or laundry between patient use. Use of the AirPal Liner is recommended as it can easily be removed and replaced with a spare liner to facilitate rapid turnaround of the AirPal Platform between patients. Only AirPal "N" Series Platforms may be laundered. See Laundry Guidelines below for more information. The CDC recommends disinfecting with the use of household chlorine bleach diluted to a 1:10 ratio of bleach to water. This solution can be applied to all ("L" & "N" Series) AirPal Platforms. Bleach solution can be applied with a suitable cloth or sponge and applied via spray bottle or bucket. All surfaces should be wiped down liberally and allowed to air dry. To speed up drying, excess solution can be removed with clean paper towels and or a clean cloth towel. Rinse or dispose of all cleaning tools. In addition to wiping down the AirPal Platform and liner it is recommended that the air supply hose end be inspected and wiped down with a disinfectant. Inspect and wipe down the interior of hose attachment point on the AirPal Platform as well. In addition to a bleach/water solution, the following disinfectants have been tested by AirPal's materials manufacturer and are safe to use on the fabrics found in AirPal Platforms. All disinfectants should be used in accordance with the manufacturer's recommended dilutions and instructions for use.

Download the AirPal cleaning instructions

Stain Removal ("L" and "N" Series):

Prior to any procedure please abide by your facility's standards for protective clothing and eyewear.

In general, stains to AirPal Platforms can be treated in the same way a common garment stain is treated. Using a standard household laundry stain remover (colorfast safe) treat the spot per manufacturer's direction - in place of a laundry stain remover, a concentrated mild detergent can be used. Work the stain for five minutes then rinse thoroughly with cold water. Remove excess rinse water with paper towels and allow to dry thoroughly. Use of a soft bristle brush may aid in stain removal.

For stubborn stains, soak the affected area in cold water and a diluted mild detergent mix of 1:5 (detergent to water). Remove from diluted solution (2 -3 hrs), rinse, and repeat stain removal procedure from above.

Laundry Procedure ("N" Series Only):

Prior to any procedure please abide by your facility's standards for protective clothing and eyewear.

"N" Series AirPal Platforms can be laundered according to the instructions below. Located at the foot-end of the AirPal Platform is a label with laundry and cleaning instructions. Verify that the AirPal Platform is an "N" Series. "L" and "N" series AirPal Platforms can be denoted by the use of different fabrics for the patient surfaces. "L" Series AirPal Platforms are a dark Navy Blue color and have a patient surface made from 'Lectrolite. The 'Lectrolite fabric is vinyl coated. "N" Series AirPal Platforms will be light blue in color. The latest models will have a Royal Blue patient surface made from Sure Chek Fusion III. This fabric has stretch characteristics and will have a little give when pulled on.

1. Soils or Strains: Wipe fabric clean with neutral suds and lukewarm water. Rinse with water.
2. Hard to Clean Spots: Use standard liquid household stain removers (colorfast) and/or soft bristle brush. Pre-soak as needed. See "Stain Removal" above.
3. Disinfection: Dilute disinfectants and/germicides as specified on manufacturer’s product label.
4. Laundering: Wash and rinse according to the “Synthetic Washing Procedure for Coated Fabrics” described below:
   
   

   Operation	Water Level	Time	Maximum Temp.	Supplies
   1st Suds	High	5 min.	120F	Neutral Soap & Alkali
   2nd Suds	High	10 min	120F	Neutral Soap
   1st Rinse	High	3 min.	120F	Water
   2nd Rinse	Low	3 min.	90F	Sour to ph 5.0

   
   
   
   
   
   

   • A slow speed machine is used. The wash wheel is stopped for drainage and refilling between each cycle.
   • Extract with centrifugal extractor.
   • Tumble dry in steam dryer (not gas) at lowest possible setting (120F maximum). All synthetic fabrics are heat sensitive. To prolong the life of your product always use the lowest temperature setting.
   • Do Not Iron. Although wrinkles may appear, they will not affect performance.
5. Strict adherence to above described laundry procedures must be maintained. Failure to follow recommended procedures may prove harmful to fabrics resulting in loss of expected useful life and voiding of warranty.

Filter and Accessory Cleaning

Filter - Located inside the AirPal Air Supply:

Warning: Electrical Hazard. Remove AirPal Air Supply from electrical outlet before following this procedure.

Prior to any procedure please abide by your facility's standards for protective clothing and eyewear.

The AirPal Platform System requires the use of the AirPal Air Supply for inflation and patient transfer. The airflow is filtered through a "sock type" filter located inside the stainless steel filter enclosure. Cleaning of the filter is considered "routine maintenance" and under no condition will it void the manufacturer's warranty to follow the filter cleaning procedure (AirPal Air Supplies are covered under warranty from date of shipment for two years). Filter cleaning schedules are dependent upon amount of use and operating environment. AirPal recommends cleaning the filter on a minimum basis of once a quarter. Filters should be replaced every two to three years or as needed.

To access the filter remove the three Phillips Head screws that attach the stainless steel filter enclosure to the main body of the motor housing. Release the ground strap (green wire) and remove the stainless steel filter enclosure off to the side. Remove the "sock type" filter (the filter is held in place by tension with elastic at the open end).

Once the filter is removed, clean under cold running water. Place clean filter in a germicidal solution and let soak for five minutes (a 1:10 solution of chlorine bleach to water can be used). Remove from germicidal solution, remove excess solution (paper towels can be used to accelerate drying - place filter between towels and pat dry) Allow the filter to thoroughly dry before reinstalling into the AirPal Air Supply.

Replace filter by performing removal steps in reverse.

AirPal Air Supply - Exterior Surfaces:

Warning: Electrical Hazard. Remove AirPal Air Supply from electrical outlet before following this procedure.

Prior to any procedure please abide by your facility's standards for protective clothing and eyewear.

Due to the environment that the AirPal Air Supply is operated in, it is recommended that the AirPal Air Supply be routinely cleaned. In between patient use or whenever soiled, the Air Supply and Hose should be wiped down with a germicidal solution (Phenolic is preferred), or as per hospital protocol for a similar type of equipment. Use a clean sponge or paper towels dampened with the germicidal solution to wipe down all exterior surfaces. Wipe up any excess cleaning solution with clean dry paper towels and dispose of or rinse out cleaning tools properly. A diluted 1:10 solution of chlorine bleach to water can be used but note that stainless steel surfaces must be immediately dried after application - chlorine residues can be aggressive to stainless steel and metals in general.

AirPal Stand - Exterior Surfaces and Storage Basket

Prior to any procedure please abide by your facility's standards for protective clothing and eyewear.

Due to the environment that the AirPal Stand is operated in, it is recommended that the AirPal Stand be routinely cleaned. In between patient use or whenever soiled, the AirPal Stand should be wiped down with a germicidal solution or as per hospital protocol for a similar type of equipment. Use a clean sponge or paper towels dampened with the germicidal solution to wipe down all exterior surfaces. Wipe up any excess cleaning solution with clean dry paper towels and dispose of or rinse out cleaning tools properly. A diluted 1:10 solution of chlorine bleach to water can be used but note that stainless steel surfaces must be immediately dried after application - chlorine residues can be aggressive to stainless steel and metals in general.

The storage basket is designed to be easily removed for cleaning. Place one hand on the stand and with your other hand push the bottom of the storage basket up and out from the retention ring. The storage basket can be cleaned in a suitable laundry sink and is also dishwasher safe. When clean and dry replace the storage basket in the retention ring and push down to seat the storage basket.